Antec ISK 110 VESA Case Review: Just About As Small As It Gets
by Dustin Sklavos on August 31, 2012 12:01 AM EST- Posted in
- Cases/Cooling/PSUs
- Mini ITX
- Antec
Testing Methodology
For testing Mini-ITX cases, we use the following standardized testbed with and without dedicated graphics cards to get a feel for how well the case handles heat and noise.
Mini-ITX Test Configuration | |
CPU |
Intel Core i3-2120 (65W TDP) |
Motherboard | Zotac Z68ITX-A-E |
Graphics Card | Intel HD 2000 IGP |
Memory | 2x2GB Crucial Ballistix Smart Tracer DDR3-1600 |
Drives | Kingston SSDNow V+ 100 64GB SSD |
CPU Cooler | SilverStone NT07-1156 with Cooler Master ThermalFusion 400 |
Power Supply | Included 90W AC Adapter |
Each case is tested with just the Core i3's integrated graphics as well as with a discrete graphics card when possible. The system is powered on and left idle for fifteen minutes, the thermal and acoustic results recorded, and then stressed by running four threads (three with a dedicated GPU) in Prime95 (in-place large FFTs) on the CPU, and OC Scanner (maximum load) is run when the dedicated GPU is installed. At the end of fiteen minutes, thermal and acoustic results are recorded. If the enclosure has a fan controller, these tests are repeated for each setting. Ambient temperature is also measured after the fifteen idle minutes but before the stress test and used to calculate the final reported results.
We try to maintain an ambient testing temperature of between 22C and 24C. Non-thermal test results aren't going to be directly comparable to the finest decimal point, but should be roughly comparable and give a broader idea of how the enclosure performs.
Thank You!
Before moving on, we'd like to thank the following vendors for providing us with the hardware used in our testbed.
- Thank you to Puget Systems for providing us with the Intel Core i3-2120.
- Thank you to Zotac for providing us with the Z68ITX-A-E motherboard.
- Thank you to Crucial for providing us with the Ballistix Smart Tracer memory.
- Thank you to Kingston for providing us with the SSDNow V+ 100 SSD.
- And thank you to SilverStone for providing us with the NT07-1156 heatsink/fan combo.
53 Comments
View All Comments
DanNeely - Friday, August 31, 2012 - link
I'm a bit surprised they didn't go with something more like a pico-psu in general. Just using 12V in instead of 19V would allow for a significantly smaller board since you'd only need to make small amounts of 3.3/5V internally and not large amounts of 12V as well. Dropping the additional conversion should also boost total system efficiency and lower wall power as a result.Lonyo - Friday, August 31, 2012 - link
Yeah, the power circuitry based on the pics looks like a lot more than I would expect to be necessary given the size of a PicoPSU (I'm using on on an ITX system with G620T and HD6450, as well as 3x3.5" HDDs with no problems).If it's an ITX system with just 2.5" drives, there should be no issues with a low power PicoPSU instead of whatever they went with.
Alex_N - Friday, August 31, 2012 - link
I built three identical systems using this case, used i7 3770S (65W quad core) for the CPU and Intel's reference mini-ITX ivy bridge motherboard. I use them for a small CPU-heavy compute cluster.Pros:
-assembly was pretty easy. I was able to fit the motherboard in without removing the PSU.
-very low power (I can run them all off one power strip)
-very low noise... can't hear them running over the AC and my desktop, even with my head next to the case and at full load (obviously depends on your CPU fan, I'm using the stock cooler fan)
-very space efficient (the other mini-ITX cases are 3X as large)
-CPU runs cool at load
Cons:
-PSU runs very hot at load. Could be partially due to the tough cable management.
-one of the PSUs was dead out of the three. Replaced it with a PicoPSU, which was much smaller (and maybe runs cooler, too, but haven't checked closely)
It's been about 4-5 months and I'm very happy with them. Quiet compute cluster, low cost, low noise, low power consumption, fast boot times (SSD + new style BIOS - UEFI?). I'd consider building these for friends/relatives who need a non-gaming PC, as well.
fic2 - Friday, August 31, 2012 - link
I am curious as to what PicoPSU you replaced the PSU with.EnzoFX - Friday, August 31, 2012 - link
I love these things, but I don't understand why they can't do proper length cables, or include cables that would just fit well, as opposed to something at standard length. Furthermore, why cant' they make some custom connectors or adapters. It must be possible, for them to create maybe even a new standard to keep cables to a minimum size and length in these type of cases. The power is only going to so few devices that it should warrant custom cables perhaps? The ease of assembling and better airflow would be worth the marginal extra cost, surely?jhoff80 - Friday, August 31, 2012 - link
...but with most new mITX boards having a mSATA slot, I'd absolutely love to see a case with 0 drive bays but that still has two PCI expansion slots (preferably with a riser) to support a dedicated GPU.Wardrop - Friday, August 31, 2012 - link
Just a shame that Antec cases are always so ugly... or maybe out of date is a better description. Would have looked awesome back around the turn of the century, but otherwise, I think Lian Li are the only one's making attractive cases of this size (or a little larger).Scannall - Friday, August 31, 2012 - link
I agree, it really does look bad. I used a Wesna case for my HTPC.http://www.shop.perfecthometheater.com/HTPC-ITX2-B...
Looks far better.
Wardrop - Saturday, September 1, 2012 - link
That Wesna case is pretty nice. Thanks for the link.Anosh - Wednesday, November 7, 2012 - link
Expect it gets to warm