Introduction

It was only one day after we released the Enermax Pro82+ and Modu82+ review that we received an e-mail from Silverstone Taiwan telling us we were wrong about the assumption that Enermax offers the quietest power supplies at the moment. Silverstone told us about their new Decathlon DA700 that is supposed to be even quieter. Our reply was naturally that Silverstone could only prove this matter by sending us a sample for review. A few days later, we had the DA700 delivered and we started testing immediately. We could tell immediately that Silverstone actually beat out Enermax, but let's get to know the power supply a little better first.


We have already tested several Silverstone PSUs, and until now they could never reach the highest efficiency levels. The build quality was and is superb and nothing to be worried about, but efficiency always tended to trail competitors - granted only by a few percent, but when you're spending a large chunk of change why not go for the best?

Silverstone is producing this unit with Impervio as the ODM, and we would have said it would be a cold day in hell before those companies would have anything to do with each other. However, with this new Decathlon Silverstone is trying a different approach from what we have previously. This unit is a fully modular power supply, which means that the user can detach all of the cables. This may not make sense at first, but this gives Silverstone at least one advantage over competitors. The company is now able to offer cable packages of different lengths. If you are running an HTPC, you will often find that cables on typical PSUs are far too long for this kind of small form factor case. Silverstone now offers a package with very short cables that can easily be used in place of the longer ones. No more bulky, long 24-pin ATX cable taking up space!


The label gives minimal information, which we are used to from Silverstone. The rail specification is rather obfuscated, requiring several perusals and the use of a calculator before you actually understand what you're reading. We have no idea why Silverstone makes it so complicated, but that's how the company does it, dating back to their beginnings. The 3.3V and 5V rails offer 24A and 30A with a combined power of 180W. That's average, similar to what we see with most other power supplies today. The DA700 comes with a 12V rail rated for up to 58A which is almost 700W already. Obviously, that load is not possible with the combined power of all three main rails; doing the necessary math, if you put a load of 180W on the 3.3V and 5V rails, that leaves 520W for the 12V rail, or 43A. Reading between the lines, then, the maximum load on the 12V rail will be somewhere between 43A and 58A, depending on the 3.3V + 5V load.

Package, Appearance and Cables
Comments Locked

20 Comments

View All Comments

  • Spacecomber - Sunday, April 27, 2008 - link

    Does Silverstone offer any lower wattage Decathlons of the same type as this reviewed model, i.e., with the same very quiet characteristics? 700 watts is just way more power than I can imagine needing for a music server/home theatre PC.

    And, I didn't understand why Silverstone and Impervio were considered to be unlikely partners. Can anyone shed a bit of light on that remark?

    Finally (and least), I think this sentence on the first page is missing a word, "However, with this new Decathlon Silverstone is trying a different approach from what we have previously [seen?]."

    Thanks.
  • Christoph Katzer - Sunday, April 27, 2008 - link

    Silverstone does have the ELEMENT series with 400 watts which is very nice as well.

    The remark on Silverstone and Impervio was made because I said once that Impervio was formed by Silverstone. I then had major complaints from Impervio coming in since there were companies wanting to stop working with them if they belonged to Silverstone.
  • Clue69Less - Wednesday, April 23, 2008 - link

    Based on the review title, I'd expected to see some comparison data. Maybe the PCP&C Silencer 750 and the Zalman HP-700 units would be good to compare if having ample power in a quiet package. Sure, this review has quantitative SPL results but it would be nice to see an actual, real-time comparison. You know, like science typically does.
  • Kanchenjunga - Wednesday, April 23, 2008 - link

    Your methodology claims a 4 decimal place accuracy but the graphs aren't even visually accurate to 1 decimal place. The graphs should also reflect identical voltage ranges for equidistant lines but they don't, the first lines above and below nominal are only half or less the voltage range as the equidistant lines in the rest of the graph. As a result the voltage drops beyond a plus or minus 1% range aren't reflected accurately in the shape of the curve.

    Also the 11.94V line in the 12V graph should be 11.64V and the 3.14V line should be labeled 3.13V if the graphs are supposed to be consistent above and below nominal.
  • Stefan555 - Tuesday, April 22, 2008 - link

    The label on the psu is not more complicated than on any other psu, its very easy to understand, I cant see what makes this label more complicated than any other label.

    No offence Chris, but are you really sure you know how to read the labels?
  • whatthehey - Tuesday, April 22, 2008 - link

    The Greater Internet Fuckwad Theory in full effect (http://www.penny-arcade.com/comic/2004/03/19/">http://www.penny-arcade.com/comic/2004/03/19/ for the uninformed).

    The label lists combined 3.3V and 5V, but nothing about the 12V. 58A and 12V works out to 696W, which means you can't count on getting anywhere near 58A from the 12V lines. And there are four 12V rails, but no mention of the breakdown of power distribution. Hell, the label doesn't even let you know there are four rails! Yes, that's so much better than, say, the way Xigmatek did their labels: http://www.anandtech.com/casecoolingpsus/showdoc.a...">http://www.anandtech.com/casecoolingpsus/showdoc.a...

    It's not a huge complaint, but given the parity between power supplies it seems to me that a lame-ass label deserves a mention. Just like your comment deserved a rebuttal. No offense, but are you sure you know how to read technical reviews?
  • jonnyGURU - Tuesday, April 22, 2008 - link


    The label lists combined 3.3V and 5V, but nothing about the 12V. 58A and 12V works out to 696W, which means you can't count on getting anywhere near 58A from the 12V lines.


    Since there is bound to be a minimum load requirement on the other rails, it is true that it would be difficult to load the +12V up to 696W without going over 700W, but I fail to see how this makes for an argument that the label is any less comprehensive. When other PSU companies list the +12V capability in watts, I hear people complain that they have to bust out a calculator and divide by 12. Is it really so hard to go from wattage to amperage and vise versa when the voltage is known?

    Unless you're using this sentence as a platform for your argument:


    Obviously, that load is not possible with the combined power of all three main rails; doing the necessary math, if you put a load of 180W on the 3.3V and 5V rails, that leaves 520W for the 12V rail, or 43A.


    I believe if you look at virtually ANY quality power supply on the market you're going to find that if you full load whatever the +3.3V and +5V combined is, that there is significantly less power available to the +12V. I say "quality" because any PSU that gives you a total wattage number that IS the sum of it's +3.3V and +5V and it's +12V is likely lying about it's actual total output capability. This has everything to do with a power supply's capability to convert AC to DC and then the unit's ability to regulate X amount of DC on the secondary side. Never does 3.3V + 5V + 12V = PSU's total capability.


    And there are four 12V rails, but no mention of the breakdown of power distribution. Hell, the label doesn't even let you know there are four rails!


    I must have missed this because nowhere could I find that this is a PSU with a split +12V rail. In fact, in this review it says: "The DA700 comes with a single 12V rail rated for up to 58A" and on SilverStone's website it says "Class-leading single +12V rail with 58A at 50?" so where are we getting four +12V rails from?
  • strikeback03 - Tuesday, April 22, 2008 - link

    Bottom of page 4: " The more important 12V rail, which is actually four separate rails, has similar good readings and always stays just above the specified 12.00V"

  • Stefan555 - Tuesday, April 22, 2008 - link

    Yes, thats a statement in the review. Silverstone sell the psu as a single rail unit. You must prove Silverstone is hiding the truth, not just make a statement out of no-where.

    Without proof the statement is worth nothing
  • Christoph Katzer - Tuesday, April 22, 2008 - link

    If someone would only look through all of the date before making comments. Please have a look in the gallery added to the Internals page. One might find a picture with the different 12V rails clearly marked on the PCB... additionally one might find the four different color markings on the yellow 12V cables on various kinds of pics from the article.

Log in

Don't have an account? Sign up now